{"id":2042,"date":"2026-07-22T08:03:47","date_gmt":"2026-07-22T08:03:47","guid":{"rendered":"https:\/\/gearrack.top\/?p=2042"},"modified":"2026-07-22T08:04:23","modified_gmt":"2026-07-22T08:04:23","slug":"ring-gears-for-robotics-and-automation","status":"publish","type":"post","link":"https:\/\/gearrack.top\/ko\/ring-gears-for-robotics-and-automation\/","title":{"rendered":"Ring Gears for Robotics and Automation"},"content":{"rendered":"
\n
\n
<\/div>\n
<\/div>\n
GEAR APPLICATION GUIDE \u00b7 RING GEAR \u00b7 R10<\/span><\/p>\n

Ring Gears for Robotics and Automation:
\nRobot Joint Drives, Harmonic Drive Alternatives and Collaborative Robot Ring Gears<\/span><\/h1>\n

Ring gears in robotics applications are at the frontier of precision gear manufacturing \u2014 the ring gear in a collaborative robot (cobot) joint drive must achieve backlash below 1 arc-minute, torsional stiffness above 500 Nm per arc-minute, and absolute position accuracy below 0.05\u00b0 over the full joint rotation range, while fitting inside the robot arm cross-section of 80\u2013120 mm OD and having a mass below 200\u2013400 grams per joint. These specifications \u2014 the combination of precision, stiffness, compactness, and low mass \u2014 push ring gear manufacturing to its technical limit and have driven the development of alternative drive principles (harmonic drives, cycloidal drives) that achieve higher precision than standard planetary at the cost of higher manufacturing complexity. This guide covers both the technical specifications of ring gears for standard high-precision planetary robot joint drives and the design principles of harmonic drive flex-splines (a special form of internal ring gear) used in precision robotic applications.<\/p>\n

20CrMnTi \u00b7 17-4 PH \u00b7 M1\u2013M5 \u00b7 DIN 3\u20135<\/span>
\n\u22641 arc-min \u00b7 \u2265500 Nm\/arc-min \u00b7 0.05\u00b0 accuracy<\/span>
\nCobot \u00b7 SCARA \u00b7 6-Axis \u00b7 AGV \u00b7 Delta \u00b7 EOAT<\/span><\/div>\n<\/div>\n<\/div>\n
\n
\n
\n

BACKLASH TARGET<\/p>\n

\u2264 1 arc-min<\/p>\n

Ring gear backlash specification for robot joint planetary drives. Industrial 6-axis robot: \u2264 1.5 arc-min. Collaborative robot (cobot): \u2264 1.0 arc-min. High-precision SCARA: \u2264 0.5 arc-min. Medical robot: \u2264 0.3 arc-min. At 1 arc-min backlash and a robot arm of 500 mm reach, the TCP (tool centre point) position uncertainty from joint backlash is approximately 0.145 mm per joint \u2014 for a 6-joint robot, total TCP uncertainty contribution from backlash alone is up to 0.87 mm<\/p>\n<\/div>\n

\n

STIFFNESS<\/p>\n

\u2265 500 Nm\/arc-min<\/p>\n

Minimum torsional stiffness for robot joint planetary ring gear stages. The joint torsional stiffness determines how much the robot arm deflects under load \u2014 at 500 Nm\/arc-min, a 100 Nm payload torque at the wrist deflects the joint by 0.2 arc-min (0.0033\u00b0), producing a TCP position error of 0.029 mm at 500 mm reach. Multiple joints compound: a 6-joint robot with all joints at 500 Nm\/arc-min and 100 Nm load can show total TCP deflection of 0.17 mm \u2014 acceptable for assembly tasks but marginal for grinding or deburring<\/p>\n<\/div>\n

\n

MODULE<\/p>\n

M1 \u2013 M5<\/p>\n

Robot joint ring gear module range. Wrist joint (smallest): M1\u2013M2, OD 40\u201380 mm. Elbow joint: M2\u2013M3, OD 80\u2013120 mm. Shoulder joint (highest torque): M3\u2013M5, OD 120\u2013200 mm. SCARA horizontal joint: M2\u2013M4. AGV wheel drive: M3\u2013M5, OD 120\u2013180 mm. Delta robot joint: M1.5\u2013M3. All DIN 4\u20135 for backlash requirement, all carburized for stiffness\/strength<\/p>\n<\/div>\n

\n

CYCLE LIFE<\/p>\n

\u2265 10,000 hrs<\/p>\n

Robot joint ring gear design life. Collaborative robot (cobot): 10,000 hours typical specification (3 years at 3,000 hours\/year in manufacturing). Industrial robot shoulder joint: 30,000 hours (10 years at 3,000 hours\/year, 3 shifts). Surgical robot: 10,000+ hours AND \u2264 1 \u03bcm total wear on tooth flanks (sterilisation-level cleanliness requirement). The ring gear must maintain its backlash specification within the design tolerance for the full design life<\/p>\n<\/div>\n<\/div>\n

\n

Robot Joint Ring Gear Engineering \u2014 Backlash, Stiffness, and the Planetary vs Harmonic Trade-Off<\/h2>\n

The robot joint drive debate between standard planetary ring gears and harmonic drive (strain wave gear) flex-splines is fundamentally a trade-off between backlash, stiffness, mass, and manufacturing cost. Standard planetary ring gears achieve the \u2264 1 arc-min backlash required for cobots at DIN 4\u20135 quality class with matched planet pitches \u2014 this is demonstrated in production by Korea Ever-Power’s printing press and packaging machine planetary gear sets, which reach 0.5\u20130.8 arc-min backlash at DIN 5. However, the standard planetary’s inherent kinematic mechanism (discretely meshing sun-planet-ring contacts at fixed pitch positions) produces a periodic torque ripple (at the planet tooth mesh frequency) that can excite structural resonances in the robot arm \u2014 particularly in the lower-stiffness carbon fibre composite arms used in cobots. The harmonic drive (a cup-shaped thin-ring flex-spline that deforms elliptically inside an internal circular spline) achieves backlash below 0.1 arc-min and near-zero torque ripple \u2014 but at 3\u20135\u00d7 the manufacturing cost of an equivalent planetary ring gear, and with a torsional stiffness that is typically 30\u201350% lower than the equivalent planetary at the same gear ratio and joint OD.<\/p>\n

Korea Ever-Power’s ring gears for robotics and automation<\/a> are manufactured in 20CrMnTi case carburized (HRC 60\u201362 tooth surface, 42CrMo4 QT carrier for the standard industrial robot and cobot market) and 17-4 PH H900 stainless (for food handling cobots and medical robots where the joint drive must withstand washdown or autoclave sterilisation). The precision level for robot ring gears (DIN 4\u20135 internal tooth, CBN-ground) requires the planet gear matched set tolerance of \u00b12 \u03bcm and the ring gear internal tooth total pitch deviation below 3 \u03bcm \u2014 parameters that push the manufacturing process to its limits at modules M1\u2013M3, where a 3 \u03bcm pitch deviation represents 0.1% of the tooth pitch of a M3 ring gear. Korea Ever-Power achieves these tolerances by processing robot ring gears on dedicated CNC internal grinding machines in a climate-controlled cell (20\u00b0C \u00b1 0.2\u00b0C) and measuring each ring gear individually on a Klingelnberg P26 gear measurement machine with 0.1 \u03bcm stylus resolution.<\/p>\n

The cobot-specific design requirements differ from standard industrial robot requirements in several key respects that affect the ring gear specification. Cobots (collaborative robots designed to work alongside humans without physical safety barriers) require a lower backlash specification than conventional industrial robots because the cobot operates under position control in the human-shared workspace \u2014 any backlash-induced position overshoot at a direction reversal could cause unintended contact with a human operator. Cobots also typically use a torque-limited control mode (the motor controller limits the torque to a level safe for human contact, typically 30\u201380 N effective force at the TCP) \u2014 this torque limitation reduces the peak torque at the ring gear to a value significantly below the structural limit of the gear, meaning the ring gear design for cobots is dominated by precision and stiffness requirements, not load capacity. The lower torque requirement at cobots allows Korea Ever-Power to use smaller modules (M1\u2013M2 for cobot wrist joints vs M3\u2013M5 for equivalent-ratio industrial robot joints) \u2014 producing a smaller, lighter ring gear that fits within the cobot’s more compact arm cross-section, while still maintaining the DIN 4 quality required for the \u2264 1 arc-min backlash specification.<\/p>\n

\"planetary
Korea Ever-Power 20CrMnTi carburized precision internal ring gear for cobot shoulder joint drive \u2014 M3, 54T internal, OD 175 mm, bore 162 mm, wall thickness 6.5 mm (thin-ring, controlled by quench constraint fixture during heat treatment), face width 28 mm, DIN 4 CBN-ground. Assembled-stage backlash: 0.8 arc-min (measured on the assembled 2-stage planetary at rated radial preload). Torsional stiffness at rated torque: 620 Nm\/arc-min. Planet gear set: 3 matched planets, pitch within \u00b12 \u03bcm. Planet bearing type: angular contact deep groove bearing (preloaded) \u2014 not needle roller \u2014 to eliminate bearing radial clearance contribution to effective backlash. The ring gear\u2019s thin wall (6.5 mm, only 1.3\u00d7 the tooth height of M3) required the quench constraint fixture during carburizing and quenching to maintain bore roundness within 0.020 mm TIR after heat treatment \u2014 without the fixture, the predicted bore distortion would have reached 0.065 mm TIR, making post-hardening internal grinding to DIN 4 impossible (the grinding stock removal required would have exceeded the available grinding allowance from the pre-hardening finish-cut). With the fixture, actual bore distortion was 0.018 mm TIR, comfortably within the DIN 4 internal grinding allowance.<\/figcaption><\/figure>\n<\/section>\n
\n

Robot and Automation Platform Ring Gear Specifications<\/h2>\n
\n
\n

6-Axis Industrial Robot Joints (J1\u2013J6)<\/h3>\n

M2\u2013M5 depending on joint, DIN 4\u20135, 20CrMnTi carburized, 2-stage planetary per joint, matched planet pitch \u00b12 \u03bcm, angular contact bearings (preloaded), backlash \u2264 1.5 arc-min, torsional stiffness \u2265 400 Nm\/arc-min, design life 30,000 hours. The 6-axis industrial robot (Fanuc, KUKA, ABB, Yaskawa, Denso, Epson) uses a planetary gearbox at each of the 6 joints \u2014 joint 1 (base rotation, highest torque) has the largest planetary ring gear (M4\u2013M5, shoulder-size), while joints 5 and 6 (wrist roll and yaw, lowest torque but also smallest OD) use the smallest ring gears (M1.5\u2013M2, wrist-size). Korea Ever-Power manufactures matched ring gear sets for all 6 joints of the major robot brands, with cross-reference to robot model and production year for aftermarket service supply.<\/p>\n

M2\u2013M5 \u00b7 DIN 4\u20135 \u00b7 30,000h \u00b7 6-joint set<\/p>\n<\/div>\n

\n

Collaborative Robot (Cobot) Joint Drives<\/h3>\n

M1\u2013M3, DIN 4, 20CrMnTi carburized or 17-4 PH (washdown variant), torque-sensing joint design (ring gear integrated with a strain gauge or piezoelectric torque sensor element for the cobot’s collision detection system), backlash \u2264 1.0 arc-min, mass \u2264 300 g per stage, design life 10,000 hours. Collaborative robots (Universal Robots, FANUC CRX, ABB GoFa, KUKA LBR, Doosan, Aubo, Techman) have become the fastest-growing segment of the industrial robotics market \u2014 their compact, lightweight design and direct human-collaboration capability drive unique ring gear requirements that standard industrial robot ring gears do not address. The torque-sensing ring gear is a Korea Ever-Power custom product where the ring gear OD integrates a precision torsional compliance element (a section of reduced wall thickness that deflects measurably under torque) with strain gauge mounting holes \u2014 allowing the ring gear to function as both the gear element and the torque sensor housing in the cobot’s integrated joint module.<\/p>\n

M1\u2013M3 \u00b7 DIN 4 \u00b7 cobot \u00b7 torque sensor option<\/p>\n<\/div>\n

\n

AGV Wheel and Pivot Drive Ring Gears<\/h3>\n

M3\u2013M5, DIN 5\u20136, 20CrMnTi carburized, compact hub-integrated design (ring gear OD doubles as the wheel hub bore \u2014 the ring is pressed into the drive wheel hub), IP67 sealing (AGVs operate in wet warehouse and manufacturing environments), design life 15,000 hours, shock resistance from floor transitions. Automated guided vehicles (AGVs) and autonomous mobile robots (AMRs) use planetary ring gears in the wheel drive assembly (the motor + planetary gearbox combination that drives each wheel) and in the pivot drive (the mechanism that steers the drive wheel module around its vertical axis for omnidirectional AGV navigation). The hub-integrated ring gear design for AGV wheel drives requires the ring gear OD to be precision-machined to the wheel hub bore tolerance \u2014 usually H7 fit \u2014 and for the ring gear to maintain this OD dimension over the 15,000+ hour life, including the thermal cycling from cold warehouse starts in \u221210\u00b0C to +40\u00b0C summer operating temperature in a Southern European or North American distribution centre.<\/p>\n

M3\u2013M5 \u00b7 hub-integrated \u00b7 IP67 \u00b7 AGV AMR<\/p>\n<\/div>\n<\/div>\n

\"Korea
Korea Ever-Power gear type overview for robotics applications \u2014 the selection between gear types for robot joints follows the joint torque and precision requirement: internal ring gears for high-ratio planetary (the dominant robot joint drive); external ring gears for rotary table and base rotation where the large-diameter external ring provides a high-accuracy angular reference; and spur or helical external gears for the robot\u2019s tool end-of-arm tooling (EOAT) quick-change mechanisms and on-board tool drives. Korea Ever-Power\u2019s robotics ring gear production covers all three applications \u2014 the same DIN 4 quality standard applies to each, since the robot\u2019s position accuracy is determined by the lowest-quality gear in the kinematic chain. A single DIN 7 ring gear at the robot base joint (for cost saving) would degrade the robot\u2019s position accuracy to the level set by the DIN 7 gear, regardless of the DIN 4 quality of the other five joints \u2014 Korea Ever-Power specifies a consistent quality class across all joints in a robot joint set to prevent this quality-chain problem.<\/figcaption><\/figure>\n<\/section>\n
\"Korea
Korea Ever-Power robot joint ring gear manufacturing facility \u2014 DIN 4 internal CBN grinding for M2\u2013M3 robot joint ring gears. The robot ring gear manufacturing process involves three precision stages that must each achieve the required accuracy without introducing datum errors from the preceding stage: (1) CNC turning of the ring blank (bore, OD, face) to \u00b10.005 mm dimensional accuracy \u2014 the bore is finish-turned oversize by the grinding allowance (0.05\u20130.08 mm on the tooth root circle for a M3 ring); (2) gear shaping of the internal tooth profile as a rough-cut (oversize by 0.03\u20130.05 mm on both tooth flanks), then the ring is sent for carburizing and quenching; (3) internal CBN grinding of the tooth profile to the final DIN 4 specification, using the outer face of the ring as the axial datum and the OD (which was finish-turned before carburizing and experienced minimal thermal distortion during the carburizing cycle) as the radial datum. The key quality control point is the transition from stage 2 (pre-hardening shape) to stage 3 (post-hardening grind) \u2014 the grinding allowance must be adequate to completely remove all heat-treatment distortion from the tooth profile, while not being so large that the grinding time becomes excessive or the CBN wheel wear rate increases above the economic limit. Korea Ever-Power specifies the grinding allowance for each robot ring gear design from the measured distortion data on the first production batch \u2014 typically 0.03\u20130.05 mm per flank for M2\u2013M3 rings with wall thickness above 5 mm.<\/figcaption><\/figure>\n
\n

Frequently Asked Questions \u2014 Ring Gears for Robotics and Automation<\/h2>\n
\n
\n
Q 01<\/span><\/p>\n

We are building a cobot arm and want to use planetary ring gears instead of harmonic drives to reduce cost. The joint OD is 90 mm and the required ratio is 30:1 at 150 Nm output. Can a planetary ring gear meet our \u2264 1 arc-min backlash requirement at this size?<\/p>\n<\/div>\n

\n

A 30:1 ratio at 150 Nm output in a 90 mm OD envelope is achievable with a 2-stage planetary ring gear configuration, and meeting \u2264 1 arc-min backlash is feasible at DIN 4 with the right design choices. Feasibility analysis for the specific requirement: Stage layout for 30:1 in 90 mm OD:<\/strong> a 2-stage planetary with each stage at 5.48:1 (5.48\u00b2 = 30.0:1) fits comfortably in 90 mm OD. Stage 1: sun M2 12T, planet \u00d73 M2 21.6T (rounded to 22T), ring M2 56T \u2014 actual ratio (56+12)\/12 = 5.67:1 (slight deviation from 5.48, adjust stage 2 accordingly). The M2 ring OD = (56+2) \u00d7 2 = 116 mm \u2014 too large. Reduce to sun 10T, planet 18T, ring 46T at M2: OD = (46+2) \u00d7 2 = 96 mm \u2014 fits within 90 mm bore with a 3 mm wall. This requires a thin-ring design with distortion control during heat treatment. Backlash at DIN 4, M2:<\/strong> Korea Ever-Power DIN 4 M2 ring gears with matched planet pitch \u00b12 \u03bcm achieve assembled-stage backlash of 0.6\u20131.0 arc-min per stage. 2-stage backlash accumulation (worst case, both stages maximum): 1.0 + 1.0 \/ stage_ratio_1 = 1.0 + 1.0\/5.67 = 1.18 arc-min \u2014 slightly above the 1.0 arc-min target. To reach \u2264 1.0 arc-min: (a) upgrade stage 1 planet matching to \u00b11.5 \u03bcm (achievable at Korea Ever-Power) to reduce stage 1 backlash to 0.7 arc-min, giving combined backlash 0.7 + 0.7\/5.67 = 0.82 arc-min \u2014 within specification; or (b) add a light spring preload on the stage 1 sun gear bearing to eliminate stage 1 gear mesh clearance. Stiffness at 90 mm OD, M2:<\/strong> Korea Ever-Power estimates 380\u2013520 Nm\/arc-min for a 2-stage M2 planetary at this OD \u2014 at the lower end of the recommended \u2265 500 Nm\/arc-min for cobots, but achievable with increased planet count (4 planets instead of 3) which improves both stiffness and load sharing. Korea Ever-Power recommends a detailed design study for this cobot joint \u2014 the 90 mm OD constraint is at the practical limit for M2 rings and requires careful thin-ring distortion management. Cost comparison with harmonic drive: Korea Ever-Power planetary ring gear set at M2 DIN 4 for this joint costs approximately 35\u201345% of the equivalent harmonic drive unit at the same ratio and output torque \u2014 significant savings at cobot production volumes of 1,000+ units per year.<\/p>\n<\/div>\n<\/div>\n

\n
Q 02<\/span><\/p>\n

Our existing Fanuc M-20iD industrial robot joints show increasing backlash after 8 years of operation. What replacement ring gear set should we order, and does Korea Ever-Power hold the Fanuc joint specification?<\/p>\n<\/div>\n

\n

Korea Ever-Power maintains a cross-reference database for major industrial robot planetary joint ring gears including Fanuc M-20iD series. For the M-20iD specifically: the 6-joint robot uses planetary gear sets at different sizes for each joint axis \u2014 J1 (base) uses the largest stage (M4 or M5), J4\u2013J6 (wrist) the smallest (M1.5\u2013M2). To confirm the exact ring gear specification for your specific M-20iD variant and serial number range (the M-20iD series includes M-20iD\/12, M-20iD\/25, M-20iD\/35 variants with potentially different joint specifications): (1) send Korea Ever-Power the robot model number and production year, and one of the worn ring gears from the highest-backlash joint (J1 or J2 is usually the first to show measurable backlash increase); (2) Korea Ever-Power will measure the worn ring, cross-reference against the database, and confirm the specification before quoting. Replacement procedure recommendation for an 8-year Fanuc M-20iD with increased backlash:<\/strong> replace all 6 joints simultaneously rather than just the one joint with the highest measured backlash. The reason: if one joint has developed 3 arc-min backlash after 8 years, the other joints will develop similar backlash within 1\u20132 years (they have the same service life and similar usage). Replacing all 6 joints in one maintenance event is significantly more cost-effective (single robot downtime, single setup cost for the maintenance crew) than making 2\u20133 separate replacements over 3 years. Korea Ever-Power supplies 6-joint complete replacement ring gear sets for major industrial robot models as a bundle \u2014 typically 12\u201318% cheaper than ordering each joint ring gear separately, and with a single lead time for all 6 joints (25\u201330 working days) to minimise the planning lead time for the scheduled maintenance event.<\/p>\n<\/div>\n<\/div>\n

\n
Q 03<\/span><\/p>\n

For a food handling cobot in a meat processing environment, what ring gear material and sealing specification should we use, and how does the NSF H1 lubricant affect the backlash over time compared to standard synthetic gear oil?<\/p>\n<\/div>\n

\n

Food handling cobot joint ring gear specification for meat processing: \uc7ac\ub8cc:<\/strong> 17-4 PH H900 stainless for all internal ring gears in the joint drive (not 20CrMnTi \u2014 carbon steel corrodes rapidly in the meat processing CIP environment even with sealed joints). 17-4 PH H900 provides HRC 38\u201343 tooth surface hardness \u2014 lower than carburized 20CrMnTi at HRC 60\u201362, but adequate for cobot joint ring gears where the tooth load is low (cobot torque-limited design) and the chemical resistance is the primary material selection driver. Sealing:<\/strong> IP69K for all joint seals \u2014 meat processing wash-down uses hot water (up to 80\u00b0C) at 80\u2013100 bar. Seal material: EPDM (not NBR \u2014 peracetic acid in meat plant CIP attacks NBR within weeks). The IP69K sealing prevents CIP chemical ingress that would contaminate the NSF H1 gear oil and attack the ring gear tooth surface. Lubricant \u2014 NSF H1 vs standard synthetic oil effect on backlash:<\/strong> NSF H1 approved food-grade PAO oils (Kl\u00fcber Summit WF 150, Castrol Optileb GT, etc.) have viscosity grades from VG 150 to VG 220, similar to standard PAO synthetic gear oils. The EHL film thickness in the ring gear tooth contact zone (which determines the effective operating clearance and thus the backlash at operating temperature) is slightly lower with NSF H1 PAO than with standard PAO because NSF H1 PAO does not contain the zinc-based extreme pressure (EP) anti-wear additives that standard gear oils use. The absence of EP additives increases the wear rate in boundary lubrication conditions (when the gear mesh momentarily operates below the minimum film thickness, which occurs at very low speed or at start from rest in cold conditions). In practice for cobot joints: the initial 500-hour running period shows slightly higher wear (0.5\u20131.0 \u03bcm additional tooth surface wear) with NSF H1 compared to standard gear oil, but after the running-in period the wear rate normalises as the surface micro-roughness has been smoothed. The total backlash increase at 10,000 hours from this NSF H1 wear differential is estimated at +0.2\u20130.4 arc-min \u2014 manageable within the cobot’s backlash budget. Korea Ever-Power pre-fills all food handling cobot ring gear stages with Kl\u00fcber Summit WF 150 (NSF H1 registered, VG 150) and validates the hot-run backlash at thermal steady state with this lubricant before dispatch.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Explore Korea Ever-Power Gear Categories<\/h2>\n

Seven precision gear product lines for industrial robots, collaborative robots, AGVs, SCARA, Delta, and automation system drives worldwide.<\/p>\n<\/div>\n

\n
\"spur<\/p>\n
\n

Spur Gears<\/a><\/p>\n

Robot EOAT \u00b7 DIN 4 \u00b7 M1\u2013M5<\/p>\n<\/div>\n<\/div>\n

\"precision<\/p>\n
\n

Helical Gears<\/a><\/p>\n

Low noise \u00b7 robot reducer \u00b7 DIN 4\u20135<\/p>\n<\/div>\n<\/div>\n

\"bevel<\/p>\n
\n

\ubca0\ubca8 \uae30\uc5b4<\/a><\/p>\n

Robot wrist \u00b7 compact angle \u00b7 DIN 4<\/p>\n<\/div>\n<\/div>\n

\"worm<\/p>\n
\n

Worm Gears<\/a><\/p>\n

Self-lock \u00b7 robot hold \u00b7 AGV actuator<\/p>\n<\/div>\n<\/div>\n

\"robot<\/p>\n
\n

Ring Gears<\/a><\/p>\n

Robot joint \u00b7 DIN 4 \u00b7 cobot \u00b7 AGV<\/p>\n<\/div>\n<\/div>\n

\"planetary<\/p>\n
\n

Planetary Gears<\/a><\/p>\n

Robot joint stage kit \u00b7 DIN 4\u20135<\/p>\n<\/div>\n<\/div>\n

\"plastic<\/p>\n
\n

Plastic Gears<\/a><\/p>\n

PEEK \u00b7 encoder \u00b7 robot sensor<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
<\/div>\n

GET A QUOTATION \u00b7 KOREA EVER-POWER<\/p>\n

Need Ring Gears for Robotics and Automation?<\/h2>\n

Korea Ever-Power manufactures precision ring gears for robot joint drives \u2014 M1\u2013M5, DIN 4\u20135 CBN-ground, \u00b12 \u03bcm matched planet pitch, assembled backlash \u2264 1.0 arc-min, torsional stiffness \u2265 500 Nm\/arc-min. 6-joint complete sets for Fanuc, KUKA, ABB, Yaskawa, and other major brands. Cobot food-handling variant in 17-4 PH stainless with NSF H1 lubricant and IP69K sealing. AGV hub-drive integrated ring gears. ISO 9001:2015 certified.<\/p>\n

Request a Quotation \u2192<\/a><\/p>\n<\/div>\n

\ud3b8\uc9d1\uc790: Cxm<\/em><\/p>\n<\/div>\n<\/div>","protected":false},"excerpt":{"rendered":"

GEAR APPLICATION GUIDE \u00b7 RING GEAR \u00b7 R10 Ring Gears for Robotics and Automation: Robot Joint Drives, Harmonic Drive Alternatives and Collaborative Robot Ring Gears Ring gears in robotics applications are at the frontier of precision gear manufacturing \u2014 the ring gear in a collaborative robot (cobot) joint drive must achieve backlash below 1 arc-minute, […]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[4566],"tags":[],"class_list":["post-2042","post","type-post","status-publish","format-standard","hentry","category-application-of-gears"],"_links":{"self":[{"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/posts\/2042","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/comments?post=2042"}],"version-history":[{"count":1,"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/posts\/2042\/revisions"}],"predecessor-version":[{"id":2045,"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/posts\/2042\/revisions\/2045"}],"wp:attachment":[{"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/media?parent=2042"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/categories?post=2042"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/gearrack.top\/ko\/wp-json\/wp\/v2\/tags?post=2042"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}