Steel Spur Gears for CNC Machine Tools:
Accuracy, Backlash and Spindle Drive Design
CNC machine tool gear drives must combine precise tooth geometry with minimal transmission error to avoid surface finish defects and dimensional errors in machined workpieces. This guide covers spur gear specification for CNC machining centre spindle drives, axis feed gearboxes, tool changer drives, and rotary indexing tables — from DIN quality class selection through to backlash elimination and lubrication requirements.
DIN 4–7 · Backlash <0.05 mm · M1–M8
Machining Centre · Lathe · Grinding · EDM
Spur Gears in CNC Machine Tool Design
CNC machine tool drive systems impose two requirements on spur gears that industrial conveyor or motor reducer applications do not: transmission error must be minimised to prevent workpiece surface finish defects, and gear geometry must be repeatable from batch to batch so that replacement gears restore the original machine accuracy without hand-fitting or adjustment. A spur gear with high transmission error in a CNC spindle gearbox produces a periodic torque fluctuation at the mesh frequency that appears as machined surface chatter marks. In a CNC rotary indexing table, tooth spacing error in the spur gear drive introduces angular indexing error that directly limits the positional accuracy of the machined features.
Korea Ever-Power’s steel spur gears for CNC machine tools are manufactured in 20CrMnTi case carburized (standard), 42CrMo4 through-hardened (medium-duty), and Cronidur 30 (stainless-bearing steel, for washdown-tolerant machine tools) — all ground to the specified DIN quality class after heat treatment, with 100% tooth profile and spacing measurement before shipment. Every CNC machine tool spur gear order from Korea Ever-Power is supplied with an individual gear measurement report in the format required by the machine tool builder’s purchasing specification.
CNC machine tools also drive spur gears at higher pitch line velocities than most industrial applications at equivalent module and power — a 10,000 RPM CNC machining centre spindle with a 2:1 spur gear speed-change stage at M3 will have a pitch line velocity of approximately 14 m/s at the high-speed stage input, requiring DIN 5 or better to avoid dynamic noise and bearing life reduction from the mesh dynamic force increment at this speed. Spur gears for CNC machine tool use are always specified with ground teeth rather than shaved teeth above PLV 6 m/s.
Transmission Error — Surface Finish Impact
Gear transmission error (TE) at the mesh frequency directly modulates the spindle or axis speed, producing a periodic velocity variation. In a turning centre, spindle TE causes waviness on the finished bore or OD surface at a spatial frequency determined by the mesh frequency ÷ surface speed. At 3,000 RPM spindle and M3 module 30T gear (mesh frequency 1,500 Hz), a workpiece turned at 100 m/min surface speed shows waviness with a spatial period of 100,000 mm/min ÷ 1,500/min = 67 mm — a visible surface pattern. Reducing TE from DIN 7 to DIN 5 reduces this amplitude by approximately 60–70%, typically bringing it below the surface finish specification limit.
Backlash in CNC Axis Drives
CNC controllers provide software backlash compensation — when the axis reverses direction, the controller commands additional motor movement equal to the programmed backlash value before beginning the actual move. This compensates for the angular dead band of the spur gear drive. Effective backlash compensation requires: (a) the actual backlash must be measured and entered accurately; (b) the backlash must be consistent and not vary with load, temperature, or wear. Korea Ever-Power CNC machine tool spur gears are supplied with backlash measured at room temperature under no-load, giving the machine tool builder a reliable starting value for backlash compensation programming.
Material for CNC Machine Tool Gears
20CrMnTi case carburized (HRC 58–62) is the standard material for CNC machine tool spur gears requiring maximum fatigue life and wear resistance. 42CrMo4 through-hardened (HB 280–340) is used for medium-duty spindle gearboxes and tool changer drives where the lower cost justifies the reduced load rating at PLV below 5 m/s. Cronidur 30 (a martensitic stainless bearing steel, similar to X30CrMoN15-1) is specified for CNC machine tools in coolant-rich environments where standard alloy steel gears would rust between production shifts — Cronidur 30 achieves HRC 58–60 through martensitic hardening without case carburization, simplifying heat treatment and minimising distortion.
CNC Machine Tool Drive Applications
DIN Quality Class Selection for CNC Machine Tool Spur Gears
BACKLASH REDUCTION METHODS
- →Tight centre distance: hold centre distance to the lower end of the tolerance range — reduces backlash to 30–50% of nominal. Requires precise housing bore positional accuracy
- →Spring-loaded scissor gear: two identical spur gears on the same hub, spring-loaded to rotate slightly apart — one gear contacts the drive flank and the other contacts the coast flank, eliminating backlash. No load-carrying in both directions simultaneously; torque limited by spring pre-load
- →Profile-shifted gear pairs: positive profile shift on both pinion and wheel increases tooth thickness and reduces backlash while keeping the correct centre distance. Standard DIN 867 profile shift coefficients allow backlash reduction of 30–60% without changing centre distance
- →Software backlash compensation: CNC controller compensates for measured backlash by adding a correction move on each reversal. Most effective when combined with physically reduced backlash gears — compensation alone is insufficient for high-speed CNC axis positioning
LUBRICATION FOR CNC GEARS
- →Spindle gearbox: ISO VG 68–100 precision spindle oil or low-viscosity gear oil. Higher viscosity causes temperature rise that affects spindle thermal expansion and dimensional accuracy
- →Axis feed gearbox: ISO VG 150–220 gear oil, splash or oil mist lubrication. Synthetic PAO preferred for extended oil-change intervals in sealed machine tool axis gearboxes
- →Tool changer and indexer: NLGI 1–2 lithium complex grease for lifetime-lubricated sealed spur gear assemblies. Grease lubrication reduces contamination risk to workpiece surfaces
- →Coolant compatibility: CNC machine tool gear oil must be compatible with the coolant emulsion used — water-based coolants can contaminate the gear oil through shaft seals. Specify coolant-resistant gear oil additive package for machines using coolant concentration above 8%
Frequently Asked Questions
Explore Korea Ever-Power Gear Categories
Seven precision gear product lines for CNC machine tools, automotive, industrial and specialist applications worldwide.
編集者: Cxm
Japanese 
English 
Italian 
Korean 
French